AutoCAD Keyboard Shortcuts

163 Responses to “AutoCAD Keyboard Shortcuts”

1. 
   Richard Binning
   August 1st, 2008 at 11:42 AM

   FYI – I havent’ been able to get Alt + F11 to open VBA since release 2005 in ADT or ACA versions…works fine in Vanilla AutoCAD (Don’t hate me Eric)

   Here’s one missing from your list: Use the ~ (tilde) symbol to open dialogs when they’ve been disabled or turned off via filedia or cmddia variables.

2. 
   bitdraughty
   October 21st, 2008 at 6:32 AM

   Do you know how to modify the shortcutsfor your express tools ?

   For example i would like to change the of layer isolate to LI

3. 
   Amy
   November 23rd, 2008 at 10:19 PM

   I too am trying to figure out how you modify these shortcuts for your express tools, please advise.
   Thanks,
   Amy

4. 
   Noriko Marshall
   November 29th, 2008 at 5:37 PM

   Tools > Customize > Edit Program Parameters

   This notepad file can be copied and transfered to other computers. It is very useful because it is portable. My coworker taught me last week.

5. 
   Noriko Marshall
   November 29th, 2008 at 5:43 PM

   If I were you, I would make sure there are no duplicates on the list. For example, LI is already taken. You might find work-around, but I would assign other command in order not to confuse the system.

6. 
   shady
   January 17th, 2009 at 11:25 PM

   thx ….u r soooo kind

7. 
   Nicole Coops
   February 2nd, 2009 at 10:07 PM

   Hi

   I have recently started working with a company that operates AutoCAD 2006 on a MAC by using a parallels system. The problem is that my shortcuts don’t work ie. ortho & osnap being the most important. Does anyone know how I can get these shortcuts to work??

8. 
   elyse
   February 11th, 2009 at 10:59 PM

   ORTHO for Mac is control+shift then “o”

9. 
   MIKE
   March 7th, 2009 at 1:30 PM

   GO TO TOOLS, CUSTOMIZE, ACADPGP THEN YOU’LL SEE ALL THE COMMAND SHORTCUT- HOW TO EDIT RIGHT CLICK HIGHLIGHT THE SHORTCUT COMMANDS AND CHANGE IT TO YOUR SHORTCUT COMMAND LET SAY REC – RECTANGLE CHANGE IT TO RC BUT MAKE SURE WHEN YOU CHANGE THE SHORTCUT IT DOES’NT HAVE THE SAME DEFAULT SHORTCUT COMMAND OF YOUR AUTOCAD AFTER YOU’VE DONE IT SAVE AND CLOSE YOUR AUTOCAD PROGRAM THEN OPEN IT AGAIN AND TYPE YOUR UPDATE COMMAND YOU’LL NOTICE THE DIFFERENCE – HOPE IT WILL HELP YOU THANKS

10. 
    frank
    May 6th, 2009 at 6:01 PM

    dc for design center

11. 
    frank
    May 6th, 2009 at 6:03 PM

    the space bar repeats the last task

12. 
    Ray
    June 4th, 2009 at 12:11 PM

    When editing acad.pgp, it is a good idea to place your new aliases at the bottom in the “– User Defined Command Aliases –” section for successful migration when you upgrade to the next version of ACAD.

    Also, I believe that those in the bottom section will take precedence over the ones above.

13. 
    mansawi b. macadaag
    June 10th, 2009 at 6:17 AM

    i’m mansawi b. macadaag of Philippines, tnx… to all, your info are very very important.

14. 
    Julie DK
    June 30th, 2009 at 2:17 AM

    CTRL+TAB to jump between open drawings.
    ALT+TAB to jump between open applications.

15. 
    Ramesh Babu
    August 13th, 2009 at 12:30 AM

    I like this shortcuts commands

16. 
    solomon
    September 25th, 2009 at 3:20 AM

    hi,

    I have installed ADT2006. First, the menu bars have not loaded when i start but fixed it with cuiload command. then when i try the general keyboard commands, none work–like PL, CO etc.
    How do i fix it?

17. 
    santosh
    October 16th, 2009 at 4:31 AM

    thank u

18. 
    Husny
    November 9th, 2009 at 7:00 PM

    huy… huy….
    thank for alll…

19. 
    vinod
    December 6th, 2009 at 9:16 AM

    Mouse wheel- zoom in and out
    Double click mouse wheel- zoom extent
    Shift+ mouse wheel pressed – 3d orbit

20. 
    rainrainrain
    December 11th, 2009 at 12:03 PM

    how about PAN? What is the shortcut key instead of typing in command?

21. 
    doyle
    December 30th, 2009 at 7:36 AM

    PAN- “P” or MMB(Middle Mouse Button) click-and-drag.

    Good luck.

22. 
    MUTHU
    April 5th, 2010 at 8:14 AM

    very useful for us thank you………..

23. 
    Deepu Vaz
    April 18th, 2010 at 9:56 PM

    can u tell me wat is VBA and wat is the use of this?

24. 
    CADDManager
    April 25th, 2010 at 6:37 PM

    Deepu,

    VBA is Visual Basic for Applications and is available to use inside AutoCAD for more advanced programming than just AutoLISP.

25. 
    Muhammad Younus
    April 26th, 2010 at 10:09 PM

    Hi Friend,
    I live in Pakistan Countray,So i looked your desing auto cad short comand,Could you tell me that.is it better course for Future.
    this time i am working in Office.Pleze guide me.
    Thanks sir

26. 
    Justin
    May 27th, 2010 at 10:04 AM

    Hello…I am trying to figure out the command for selecting all objects of the same layer that I already have selected. I have seen it used before and it would be helpful for me. Thanks

27. 
    C.Nagarajan
    July 2nd, 2010 at 6:45 AM

    please publish 3d commands clearly.
    thank you.

28. 
    SONALI AHUJA
    July 13th, 2010 at 12:23 AM

    WHAT IS SHORT CUT COMMAND IN AUTOCAD FOR WRITING ±

29. 
    CADDManager
    July 13th, 2010 at 7:56 AM

    I think it is %%p

    Type that in an then place it. After it is placed – it should change the Control Code to plus/minus

    Mark

30. 
    RAVI
    July 29th, 2010 at 11:49 PM

    WHICH COMMANDS MOSTLY USED IN 3D CAD DRAWINGS

31. 
    EVE
    August 4th, 2010 at 3:12 AM

    Hello,
    Thank you for this list!
    I want change the toggle ortho command. Is it possible to use ENTER instead of F8?!???

32. 
    ram
    August 10th, 2010 at 10:35 PM

    thank u

33. 
    Alison
    August 18th, 2010 at 7:16 PM

    Is there a list of keystrokes for the Mac keyboard/mouse – none of my PC functions work on autocad anymore now that I’m using a new Mac. I’m going insane. I am totally handicapped on my new Mac. Please help urgently anybody!!!

34. 
    mido
    August 28th, 2010 at 8:33 AM

    to SONALI AHUJA :

    try to hold on alt & type “00177″

35. 
    Sudha
    September 3rd, 2010 at 3:49 AM

    Is there any keystrokes for the commands break at point,revision cloud,extrude faces & 3dmove?

36. 
    pendurkar prakash
    September 7th, 2010 at 4:04 AM

    thanks ,,,,,,,,,,,,,,

37. 
    zain
    October 8th, 2010 at 2:37 AM

    Hi,

    i installed autocad 2006 but when it is installd its menu bar show it is student version and this text also written in printed paper with sketch.kindly tell me what can i do for this problem.

38. 
    SELVAM
    October 10th, 2010 at 10:18 PM

    thank u so much……………

39. 
    Chimaobi
    October 17th, 2010 at 2:31 PM

    Pls how do i erase part of a line or part of an arc without erasing the whole line or arc?

40. 
    João
    October 25th, 2010 at 10:48 AM

    Does anyone figure it out how to customize keyboards shortcuts in AutoCad 2011 for Mac?

41. 
    Dr. CADD
    October 28th, 2010 at 5:04 PM

    Too bad Autodesk did not think of putting an accelerator key combination in to turn the View Cube on and off…

42. 
    DLO
    November 16th, 2010 at 2:58 PM

    @ Chimaobi.

    1. Draw a line where you want your break to be.
    2. Type TR (shortcut) to Trim.
    3. Select cutting line
    4. right click or enter
    5. select side of line or arc you want cut off.
    6. delete temporary cutting line if needed.

43. 
    SAJJAD AHMED DOGAR
    November 24th, 2010 at 5:21 AM

    HI,
    I AM SAJJAD AHMED
    I AM STRUCTURE DESIGN ENGINEER IN AQC (JV) COMPANY IN LIBYA.

    I WANT TO SAY SOME THING.

    I AM VERY THANKS FULL OF CADDManager Blog.
    THEY SHARE THIS CHORT KEYS ON SITE.
    I USE THIS SHORT KEYS.
    I GET TO MUCH BENEFIT FROM THIS SHORT KEYS.
    I USE THESE SHORT KEYS AND SAVE TIME AND FINISH WORK QUIKLY.
    REALY I AM VERY THANKS FULL OF CAD MANAGER.
    THANKS YOU VERY VERY MUCH.

44. 
    jeremy
    December 10th, 2010 at 2:48 PM

    a list of CAD commands can be found in the

    1 menu

    2 files

    3 function keys

    4 contents list

45. 
    HARSHA G.M.
    December 22nd, 2010 at 12:14 AM

    SIR,
    I AM HARSHA G.M.
    I AM STRUCTURE DESIGN ENGINEER IN CES COMPANY IN BANGALORE, INDIA
    I AM VERY THANKS FULL OF CADDManager Blog.

    SIR, CAN U GIVE SOME EXAMPLE ,REGARDING MACRO ….
    HOW TO CREATE, WHERE CAN IT BE USED ….

    THANKS YOU….

46. 
    HARSHA G.M.
    December 22nd, 2010 at 3:16 AM

    SIR,

    I AM WORKING IN AUTOCAD CIVIL 3D (COUNTOUR,ALIGNMENT,L-SEC,CROSS-SEC)
    DO U HAVE ANY SPECIAL COMMANDS OR TRICKY COMMANDS…

    SIR, REGARDING ASSEMBLY, DAYLIGHT, CORRIDOR….

    THANKS YOU….

47. 
    harsha
    December 27th, 2010 at 4:56 AM

    HEllo this is harsha frm bangalore.
    Can any one tel me the shortcut key for ‘break at point’. im not getting that shortcut from any website. So someone send me.

48. 
    de mash
    January 11th, 2011 at 12:07 AM

    thanks so much CADDManager Blog.

49. 
    Josh
    January 25th, 2011 at 6:35 AM

    Is there a way to set up quick key to select specific layers? I often have to keep switching between layers and want a faster way of doing it.

50. 
    Asgar khan Azmi
    February 10th, 2011 at 12:14 AM

    SIR,
    I AM Asgar Khan
    I AM ELECTRICAL DRAUGHTSMEN ENGINEER IN SBG COMPANY IN KSA,
    I AM VERY THANKS FULL OF CADDManager Blog.

    SIR, CAN U GIVE SOME EXAMPLE ,REGARDING MACRO ….
    HOW TO CREATE, WHERE CAN IT BE USED ….

    THANKS YOU….

51. 
    saif
    February 12th, 2011 at 4:46 AM

    thankyou

52. 
    noorul mubeen, ME CIVIL.,
    February 16th, 2011 at 2:54 AM

    I AM VERY THANKS FULL OF CADDManager Blog.

53. 
    mike
    February 28th, 2011 at 10:59 PM

    overkill : to delete the overlapped lines

54. 
    jassi
    March 14th, 2011 at 10:45 PM

    cooooLLLLLLLLLL…….

55. 
    THANU PATIL 9594634610
    March 18th, 2011 at 2:07 AM

    SAJJAD AHMED DOGAR

    HI,
    I AM THANU R PATIL
    I AM MECHNICAL DESIGN ENGINEER IN TEXOL EGG. COMPANY IN PUNE.

    I WANT TO SAY SOME THING.

    I AM VERY THANKS FULL OF CADDManager Blog.
    THEY SHARE THIS SHORTCUT KEYS ON SITE.
    I USE THIS SHORT KEYS.
    I GET TO MUCH BENEFIT FROM THIS SHORT KEYS.
    I USE THESE SHORT KEYS AND SAVE TIME AND FINISH WORK QUIKLY.
    REALY I AM VERY THANKS FULL OF CAD MANAGER.
    THANKS YOU VERY VERY MUCH.

56. 
    AFZAL HUSAIN
    March 20th, 2011 at 9:03 AM

    HI
    I M AFZAL HUSAIN RIZVI
    I USE THESE SHORT KEYS AND SAVE TIME AND FINISH WORK QUIKLY.
    I thanks for these shortcuts commands.

57. 
    THANU PATIL
    March 21st, 2011 at 11:31 PM

    HI,
    I AM THANU R PATIL
    I AM MECHNICAL DESIGN ENGINEER IN TEXOL EGG. COMPANY IN PUNE.

    I WANT TO SAY SOME THING.

    I AM VERY THANKS FULL OF CADDManager Blog.
    THEY SHARE THIS SHORTCUT KEYS ON SITE.
    I USE THIS SHORT KEYS.
    I GET TO MUCH BENEFIT FROM THIS SHORT KEYS.
    I USE THESE SHORT KEYS AND SAVE TIME AND FINISH WORK QUIKLY.
    REALY I AM VERY THANKS FULL OF CAD MANAGER.
    THANKS YOU VERY VERY MUCH.

58. 
    Pasky
    March 30th, 2011 at 3:16 AM

    Sir,

    I’m using ACAD08 in the office here in Japan, when loading .cui files I accidentally press the unload of acad.cui and the all the commands have gone but I managed to restore the buttons by loading again the acad.cui files but there’s 1 more problem. The shortcut command that is input on the command line did not work, you must type the whole command to accept it meaning if you type “L” for line it will not work, you must type “LINE” to execute.. I’m not a japanese so it is very hard for me to read the option..

    Thanks in advance..

59. 
    Nauman khan
    April 6th, 2011 at 12:48 AM

    thank you

60. 
    nithin
    April 16th, 2011 at 4:20 AM

    thanks so much

61. 
    Raqib
    April 30th, 2011 at 10:52 PM

    hi guys me new to this forum,

    want to make a shortcut for Break At Point command even it works with (_break) but me want to make it something like (BP) i created a lisp but it’s annoying that every time you have to load the Lisp can you pleas help me .

    Many thank in Advance

62. 
    mohan
    May 5th, 2011 at 9:02 AM

    Thanks cad masters.

63. 
    Yogi Nayak Engineer
    May 8th, 2011 at 3:06 AM

    sir,
    I’m using autocad 06 plz tell me shorcuts command 3D for desgine

64. 
    aras
    May 11th, 2011 at 2:46 PM

    not completely but thax..!

65. 
    jennifer
    May 15th, 2011 at 1:42 AM

    can u give me some code samples of that coz i find difficulties in that area.

66. 
    pandian
    May 25th, 2011 at 11:53 PM

    I’m using autocad 2007 plz tell me shorcuts command 3D for desgine

67. 
    MUHAMMAD IMRAN KHAN
    June 10th, 2011 at 8:30 AM

    I AM VERY HAPPY.
    SHORT CUT KEYS IS MORE HELP FULL FOR MY TRAINING.

68. 
    Naeem
    June 14th, 2011 at 12:27 PM

    hi.. I have problem with Pan in Cad. it is not working directly on mouse. when i click to pan from Mouse it open up some properties. So how can i fix it..?

69. 
    aditya
    June 17th, 2011 at 7:54 AM

    please send me 3d command list with how to use?

70. 
    LAKSHMA REDDY AKKALA
    June 27th, 2011 at 3:59 AM

    Please send me total 3d commends

71. 
    sohail afridi
    July 12th, 2011 at 7:45 AM

    sir plz send me autocad complete 2d commands list wiht how it is used. i shell be very thankful to u.

72. 
    anis krishnan
    July 16th, 2011 at 6:56 AM

    please send the command and how to use of that commands

73. 
    bhatt kiran
    July 17th, 2011 at 2:28 AM

    Dear Sir or Madam
    i just 1 month start the qutocad drawing making but i dont have any short key and which type of function to apply, please sand me all list
    Thanking You
    Bhatt Kiran

74. 
    samuel
    July 17th, 2011 at 10:16 PM

    thinks for the code for autocad…

75. 
    Ronalda
    July 22nd, 2011 at 2:58 AM

    Hello

    How do I change the shortcut keys with ctrl+??

    I know to open the Layer properties manager it’s LA but want to close it again for eg. you do with ctrl+1 opening and closes the properties.

    Thank you
    Ronalda

76. 
    Rajiv
    July 24th, 2011 at 10:48 PM

    Hey ronalda

    That is very easy not only for this Layer window u can use this all other windows also Alt-Space bar than “C”

77. 
    asrar
    July 24th, 2011 at 11:49 PM

    I need the short key of text align command (Torient)

78. 
    MUHAMMAD MAZHAR IQBAL
    July 26th, 2011 at 12:40 AM

    sir i want to learn the design of wheat thresher on autocad 2004 kindly give me some procedure pzzzzzzzzzzz

79. 
    dennis
    July 31st, 2011 at 4:51 PM

    is this all the commands? there are so many hehe thanks to this website

80. 
    REETESHSAHU
    August 9th, 2011 at 10:16 AM

    dear sir madem sir plz send me autocad complete 2d commands list wiht how it is used. i shell be very thankful to u.

81. 
    nasir
    August 10th, 2011 at 1:02 AM

    hi this is really cool site

82. 
    T
    August 13th, 2011 at 9:17 PM

    Does anyone know how to jump straight to the command line with a keyboard shortcut.

83. 
    Syed Tajuddin
    August 14th, 2011 at 10:21 PM

    Hi,

    i am Syed Tajuddin thanks for this 2D Commands give i have but please one help me total 3D commands please send this my E-mail

    Thank You

84. 
    Sharif Shaikh
    August 27th, 2011 at 12:54 PM

    Sharif Shaikh
    I am a Civil Engineer in Government of Maharashtra(India).
    I extremely thankful cadmanager for the Autocad shortcuts.
    Plz.show some shortcut for switching in between the layers.

85. 
    CADDManager
    August 27th, 2011 at 2:06 PM

    Sharif,

    Let me see what I can find. Did you see this page from my old site?

    http://www.caddmanager.com/Programming.html

    Mark

86. 
    Jon
    September 3rd, 2011 at 4:23 PM

    does it contain all the shortcuts that exist in the program?
    does it the same shortcut for all the versions? 2007-2012?

87. 
    Jon
    September 3rd, 2011 at 4:24 PM

    does any command gets to have its own shortcuts? or only some of the commands?

88. 
    Jason
    September 9th, 2011 at 7:04 AM

    I’m using Autocad 2012 and have somehow managed to accidentally disable my key commands. “L” no longer works for line, “M” for move, etc. But if I type the whole command out “line”, “move” it works, not exactly a shortcut anymore though.

89. 
    amol
    September 14th, 2011 at 11:12 PM

    thank you for service comand’s

90. 
    CADDManager
    September 15th, 2011 at 1:04 PM

    Jon,

    These are the shortcuts that Autodesk has defined for the Commands.

91. 
    CADDManager
    September 15th, 2011 at 1:07 PM

    Jason
    Try a repair or reinstall or just look for the files acad.pgp or keyboardshortcuts.txt for your version. That is where the shortcuts are stored.
    Mark

92. 
    zubair
    September 16th, 2011 at 11:12 AM

    hide toollbars unhide ….. window_ workspace _autocad defult

93. 
    less is more
    September 19th, 2011 at 2:27 AM

    Shortcuts command is very helpful… thank you

94. 
    Edwin
    September 26th, 2011 at 2:09 PM

    Thanks for all the shortcuts! It is good to learn everyone and try to implement them for different things. also, depending on the AutoCAD package you have, there may be more commands, such as in AutoCAD Mechanical.

95. 
    sri
    October 7th, 2011 at 7:36 PM

    Some body advice me why ‘F’ keys are functioning only when the ‘fn’ key is pressed. To get isometric direction changed, I have to press fn 1st and then F5. This has to be done each time i need to change the isometric direction.

96. 
    sri
    October 7th, 2011 at 7:42 PM

    How do I convert ‘fn+F5′ command in to ‘F5′ command??

97. 
    shadab
    October 11th, 2011 at 11:37 PM

    Do you know how to modify the shortcutsfor your express tools ?

    For example i would like to change dimasonal

98. 
    dj
    October 11th, 2011 at 11:44 PM

    hi.. I have problem with Pan in Cad. it is not working directly on mouse. when i click to pan from Mouse it open up some properties. So how can i fix it..?

99. 
    balasuriya N.M.
    October 28th, 2011 at 8:02 AM

    thank you very much. nice work.

100. 
     Tahir
     November 1st, 2011 at 8:41 PM

     I need to know short key of Auto cad 3D the extrution of Path how we extrude the path
     Thanks

101. 
     y.s.varma
     November 9th, 2011 at 7:44 AM

     Hi,

     Well iam faceing a problem while when i selecting an object.
     Some time it will select but not every time.
     Iam using AUTO CAD 2005 MAP.
     So is there any command Whcic starts with Symbol like this as shown below..

     ~
     I am sure that a command will be there afer this symbol..

     Pls try to help me

102. 
     satre ganesh
     November 15th, 2011 at 6:29 AM

     i like this shorts keys. thangs for cad manager

103. 
     RAJESH KEWAL
     November 21st, 2011 at 10:20 AM

     Shortcuts commands very helpfull in my job thanks

104. 
     ASIF IQBAL WAZIR
     November 23rd, 2011 at 12:58 AM

     Thank you…………………..

105. 
     megan
     November 28th, 2011 at 9:01 PM

     CADDmanager -

     I am a short cut key command user – I use CTRL+ (learned drafting on a Mac with Vectorworks) for most of my commands, and thought I would share with others how to customize. You can change any of the standard CTRL+ commands listed above, and add new ones for any other command by going to (in 2012) manage > CUI Interface > customization in all files (table) + Keyboard Shortcuts + shortcut keys >> commands will be shown on the right hand side, you can double-click any of the commands to edit the shortcut keys.

     To create new short cut keys for commands not already listed, drag any command from the Command List in the table below to the short cut key list and you will be able to edit and create a new shortcut key command just like for the others. You can also add SHIFT to any CTRL command if you run out of simple letter commands.

     I am a Mac user and learned Cad with the mac based quick keys, so I’m sharing for any others like me. And personally I think CTRL commands are infinitely faster than any other way to interface…CTRL+Key is one key stroke, when most typed commands are at least 2-3 clicks and enter, not to mention hunting for tool bar commands…just sayin

106. 
     Hasir
     December 2nd, 2011 at 11:48 PM

     Its really amazing sofware

107. 
     Hasirolavanna kampiliparamba
     December 2nd, 2011 at 11:52 PM

     Its smooth and very help full software

108. 
     Rahul Saxsena
     December 4th, 2011 at 12:08 AM

     can any one tell me pls how to draw a dotted line in auto cad 2011.
     or anyway to convert a simple line into a dotted line?

109. 
     dinessh
     December 5th, 2011 at 12:31 AM

     veery thankfull to each & every person who are involving in this work for preparing the shortcut keys

110. 
     Misaki Takima
     December 9th, 2011 at 6:02 AM

     Having shortcuts is really a benefit….

     i really like it!

     its reeally worth it…
     haha, XD

111. 
     Md Viqaas
     December 10th, 2011 at 3:06 AM

     Hyee
     Sir i want complete 3d commands please send this commands

112. 
     Syed Muhammad Khurshid Akhtar
     December 11th, 2011 at 8:14 PM

     Hellow
     I thanked to you that it is a very helpful for me.
     I hope that it is most useful for auto cad’s students.

113. 
     surya singh Rajput
     December 20th, 2011 at 3:48 AM

     pls sent me short cut commend in auto cad a to Z

114. 
     KUNAL
     December 21st, 2011 at 9:34 PM

     thank you

115. 
     Tom
     January 3rd, 2012 at 12:02 AM

     the best answer:

     MIKE
     March 7th, 2009 at 1:30 PM

     editing acad.pgp is so easy, and i spent an hour searching the different menus and options in tools>customise with no luck.

116. 
     smita
     January 9th, 2012 at 2:09 AM

     i wanna full tutorial for autocadd 2008

     regards
     smita

117. 
     SIVA RIDDICK
     January 14th, 2012 at 1:23 AM

     Hello
     I Thanked to all cad MANAGER.Because this all very helpful for all students & designer also me. Repeat again thanks to all.

118. 
     Amit
     January 16th, 2012 at 9:47 AM

     Its a very interesting shoftwear

119. 
     mc
     February 12th, 2012 at 11:03 AM

     Hi!
     Im trying to figure out how I can get back to my old commands idk what i did but first i was erasing with my erase key <- and no i cant do it , and other thing that change is that i was editing my text with double click on the word and now i cant :S . thanks

120. 
     Anees
     March 1st, 2012 at 11:04 PM

     hai,
     thank you very much

121. 
     bamidele abubakar olawale
     March 13th, 2012 at 4:19 AM

     Am very glad to know this kind of page in my life, its a nice websie to visit. thanks

122. 
     martyn
     March 15th, 2012 at 5:06 AM

     im using autocad 2007 on an i mac using vmware.
     im also using a windows mouse , but i cant get the pan to work ie the middle wheel. every time i push it and move the mouse the mac gestures cut in and the whole screen swipes away and i end up on the mission control .

     very annoying ,

     iv turned off the gestures onm the mac desktop but they continue to work withing vnware.

     also i need to configure the centre wheel to pan when i hold it down. at the moment i have to hold down the command key on the keyboard and hold the left mouse button down and move the mouse..

     any advice would be much appriciated

     martyn

123. 
     Rakesh Kumar Nohbar
     March 16th, 2012 at 2:04 AM

     I am very glad to know that kind of page in my life, its a very nice website to visit. & I really very thakfull of cad manager

124. 
     CADDManager
     March 17th, 2012 at 6:52 AM

     My buddy, Bill Adams, suggests that you try disabling/enabling Smart Mouse in the VM settings

125. 
     Morish.J
     March 21st, 2012 at 9:16 PM

     Thank You, AutoCAD Shortcuts very helpfull………

126. 
     Stalin panisamy
     March 21st, 2012 at 10:14 PM

     Thank you..

127. 
     ansar
     April 2nd, 2012 at 11:34 PM

     good short cut commands

128. 
     P.S.NAGARJU
     April 3rd, 2012 at 2:57 AM

     THANK YOU FOR AUTOCAD SHORT KEYS

129. 
     P.S.NAGARJU
     April 3rd, 2012 at 2:58 AM

     THANK YOU FOR AUTO CAD SHORT KEYS

130. 
     Nishanth
     April 10th, 2012 at 2:40 AM

     Thank you
     For AUTO CAD SHORT COMMANDS

131. 
     wasim
     April 21st, 2012 at 11:17 PM

     thank you for cadd maneger

132. 
     haris
     May 1st, 2012 at 9:20 PM

     Shortcuts command is very helpful… thank you

133. 
     roop sudarshan raju
     May 7th, 2012 at 4:25 AM

     what a matter of cad manager of this website . this is the to use of short cuts of the improvement of the speed in autocad . your website is very luck for me .this is the matter i am written in .

134. 
     saurabh
     May 11th, 2012 at 4:08 AM

     THANK YOU FOR AUTO CAD SHORT KEYS

135. 
     Johny
     May 15th, 2012 at 12:20 PM

     Greetings!

     You could make an AutoCAD keyboard from an ordinary keyboard using this simple tutorial. The whole process will take about 15 minutes!

     http://forums.autodesk.com/t5/.....-p/3456714

136. 
     Shahzad Safdar
     May 16th, 2012 at 9:15 PM

     Salam to All,
     Dear blog manager and visitors,
     I wanna become an AutoCAD professional in Civil. But I’ve done Diploma in Mechanical engineering. Kindly give me your suggestion what should I choose for AutoCAD Civil or Mechanical? Which will much batter and easy to learn for me..
     Thanks in Advance.

137. 
     Shahzad Safdar
     May 16th, 2012 at 9:22 PM

     Which AutoCAD is easy to learn and work ‘Civil or Mechanical’?

138. 
     ramzan
     May 22nd, 2012 at 10:54 AM

     plz send me complete information & training for Autocad 2006

139. 
     SUNNY MENIA
     June 9th, 2012 at 3:22 AM

     THANKS TO HELP ME FOR THIS AUTOCAD COMMANDS.SUNNY

140. 
     pradep singh patwal
     June 11th, 2012 at 3:11 AM

     what writting cad command for 1 1/2

141. 
     indrajit
     June 20th, 2012 at 5:06 AM

     thank you so much cadd manager…………..

142. 
     junrie
     July 1st, 2012 at 8:56 PM

     Hi..you can customize shortcut command by simply typing “aliasedit” then change line, rectangles into your desired shortcut

143. 
     pravin
     July 13th, 2012 at 12:45 AM

     thanks

144. 
     pravin
     July 13th, 2012 at 12:47 AM

     plz send me complete information & training for Autocad 2010

145. 
     nijil
     July 16th, 2012 at 12:40 AM

     hi
     im nijil

     I’m very thankful to this blog to give this short-keys, which save my time when i’m at work.

146. 
     k.N.chavda
     July 19th, 2012 at 12:28 AM

     lots of thanks.

147. 
     CR
     July 23rd, 2012 at 10:20 AM

     Does anyone have the shortcuts for AutoCad 2012 for Mac?

     Thank you!

148. 
     aiman
     August 15th, 2012 at 8:54 PM

     how to use VBA Editor??
     tq…

149. 
     Uppli
     August 16th, 2012 at 8:01 AM

     Please send autocad details and shortcut keys up to date information

     Thanks and Regards,
     Uppli

150. 
     Rocky
     August 18th, 2012 at 2:45 AM

     LINE WITH KEYED ENTRY : Example, draw a line 2 feet long, at 45 degrees north of the x-axis.
     LINE, choose a starting point with the mouse, specify next point, type : @2’<45, ENTER
     @ = from the start point
     2’ = the distance
     < = AutoCAD code
     45 = the angle, in degrees

151. 
     sushant manohar dalvi
     August 24th, 2012 at 4:48 AM

     CADDmanager -

     Sir i want complete 3d commands please send this commands

152. 
     kh.muktadir
     August 26th, 2012 at 9:16 AM

     Thanks for the help. You people have done a great job. Keep it up. Wish
     you all the luck…………………………………………..

153. 
     asad
     September 10th, 2012 at 12:19 PM

     SALAM
     my question in what is the short key of auto cad command break at point….

154. 
     GAB
     September 12th, 2012 at 10:57 AM

     OTRACK is not there ?

155. 
     anandhan
     October 2nd, 2012 at 3:18 AM

     this command very useful for all planners.thank you.

156. 
     Firoz
     October 21st, 2012 at 5:57 AM

     Thank these commands are use full to me

157. 
     Z
     October 21st, 2012 at 1:43 PM

     Hi,
     I don`t know what happened to my commands, but suddenly it`s messed up. For example when I want to move something, I select the object then press M and it asks again to select the object, or it won`t delete anything,..
     Can anybody help?
     Thanks!

158. 
     shamsi
     October 28th, 2012 at 7:55 AM

     haiiii thanks

159. 
     Lalit Semwal
     December 20th, 2012 at 3:55 AM

     what is alternative command used for mapskinmap in autocad 2010

160. 
     lovekaran
     January 2nd, 2013 at 2:24 AM

     how we convert the autocad file into jpg file formate??????

161. 
     akhil kumar
     January 20th, 2013 at 6:05 AM

     This commanad very usefull thank uuuuu….

162. 
     akhil kumar
     January 20th, 2013 at 6:08 AM

     Thanks

163. 
     Nusrath
     March 26th, 2013 at 4:02 AM

     thank u\

Leave a Reply